Tough IP 65 Protection

The Disto E7500i is protected against water, dust and shock with a IP65 protection class rating.

To obtain an IP65 rating, the case must be tight enough to provide complete protection from dust entering any of the electronic components.

It also can sustain water projected by nozzle against the enclosure from any direction without harmful effects after 3 minutes of continuous spraying.

Make quick profile measurements

The Disto E7500i displays height and distance differences to an established reference point. This allows you to quickly make profile measurements without using more expensive equipment.

This function can also be used to check levelness of floors, if crossbeams are straight, and many other applications.

Simply target the device on a known reference mark and then measure the height differences of other points relative to this. If the measured points are taken all in one direction, the profile of the ground can be determined from the measured horizontal differences and the height differences.

Your Disto E7500i comes complete with:

• Holster with belt loop
• Lanyard/Hand Loop
• 2 AA Batteries
• Quick Start Function Card
• Leica Protect Service Card
• Calibration Certificate Silver

Functions

▼

Minimum/Maximum Measurement

In Min/Max mode, you "sweep" the laser point into a corner. The longest measurement is recorded. Very useful for accurate diagonal room or window/door measurements.

◄

Area & Volume Measurement

To get the area of a ceiling, floor, wall, or the volume of a room, you only need two or three measurements. No need to write down the individual values! The precise result is calculated automatically and shown on the display.

◄

Digital Point Finder

The integrated digital Point-Finder, with a 4x zoom and color display, makes finding the target at long distances a breeze. Its high resolution capability provides a sharp, crystal-clear image, allowing measurements to be taken even in glaring sunshine.

◄

Room Angle / Triangle

The triangle function helps you to calculate, quickly and efficiently, the area of a multi-cornered room. Divide the room into imaginary triangles. Using only three measurements, determine the area of each triangle, which you can add up cumulatively. Pressing a key gives you a detailed display of the room angle, so that you can quickly check whether it is a right angle.

◄

Painter

With this function you can determine the total wall area of a room without having to note down any intermediate results. Simply measure the lengths of the walls which you can add or subtract as required. Finally measure the room height, which is then automatically multiplied by the previously calculated value. 

◄

Pythagoras

Using the tripod, you can measure distances indirectly, horizontally and vertically.The Leica DISTO calculates the result automatically for you from three measurements. Functions such as automatic minimum and maximum measurements help you to measure the right point.

Partial heights, e.g. balcony or window heights, are determined by Pythagoras. 

◄

360° Tilt Sensor

The tilt sensors in the Leica DISTO can measure inclinations up to +45°, or even have a measurement range of 360°. This means you can measure inclinations over your head. This is particularly useful for determining roof slopes. 

◄

Smart Horizontal Mode

The desired horizontal distance is determined using the tilt measurement, event if the object cannot be directly targeted horizontally. This is very helpful if there are obstacles, e.g. walls, hedges or people, between the instrument and the target.

◄

Height Tracking

You can determine the heights of buildings or trees that have no suitable reflective points by using the height tracking function. Target with the digital point finder on the bottom point of the height to be measured and take a measurement. Then target with the laser on the top point of the object. The display then shows the height.

◄

Stake Out

One or two different distances (a and b) can be entered into the device and then used to subtract from defined measured lengths. The display always shows the current stake-out distance and a direction arrow. At a distance of 0.1m to the next stake-out point an acoustic signal sounds.

◄

Height Profile Measurement

Target the device on a known reference mark and then measure the height differences of other points relative to this. If the measured points are taken all in one direction the profile of the ground can be determined from the measured horizontal distances and the height differences.

◄

Add and Subtract Measurements

It's not always so simple as taking one shot to get the measurement you need. Sometimes its handy to add multiple shots together, or subtract a negative space from a measurement. As you use the Add/Subtract function, the final result is displayed in the main line, and the last measurement taken is shown above.

◄

Timer

Set a timer to delay a measurement the same way you would with the shutter on a digital camera.

◄

Personal Favorite Functions

With over 20 functions, chances are you are going to use one or two more than the rest. This Favorites function lets you bookmark your most-used functions on the tabs at the bottom of the touch screen.

◄

Trapezium

The Trapezium Function is useful for determining the length and slope of a roof section, and the area it covers. The DISTO uses the its internal tilt sensor to calculate the angle and the distance between the shots, which means you can measure roofs accurately from the ground.

◄

Sloped Object

Indirect distance measuring between two points. The reported measurements also include the horizontal distance between the two points, the vertical distance between the two points, and the angle between the points.

◄

Multi-Function End Piece

Whether measuring out of corners, slots or from edges, with this end-piece you are prepared for all measuring situations. The instrument detects the end-piece automatically, which helps you avoid expensive measuring errors.